Yes, we do offer hubcaps for the Malone EcoLight Sport Trailer part # MAL53FR. I recommend the Phoenix USA QuickTrim Hub Cover for Trailer Wheels part # QT545C which just simply installs over the lug nuts improving the overall look of the wheels and providing additional protection. It's also available in black as well using the Phoenix USA QuickTrim Hub Cover for Trailer Wheels part # PXQT545BHS. view full answer...
I was able to go out to the warehouse and measure the diameter of the hole on the # WM9003-4 for the hubcap that these will snap into and got 1.327 or about 1-1/8 inches. I also measured the nut impression size and got 1.037 or about 1-1/32 inches. view full answer...
Well since the Phoenix USA Baby Moon Hubcap # PX1307SS will only work with conventional wheels that are up to 15", your 2005 Toyota Tundra with 16" wheels are going to be too big.
For a 16" wheel we have the Phoenix USA Baby Moon Hubcap # PX1309SS. These will work with 16" wheels, has an overall measurement of 12" x 3", and an inner diameter of 11-11/16".
This hubcap might seem to be a bit too large for your wheel, however as long as your wheel has a 6 on 5-1/2" or 8 on 6-1/2" bolt pattern... view full answer...
We have a chrome plated baby moon cover part # AM90086 that fits the trailer wheel part # AM20214 but we do not have a stainless steel option. view full answer...
I went out to the warehouse and pulled Baby Moon hubcap # AM90086 It measures 2-11/16 inches from the inside center out to the edge. But please note that this hubcap fits 13 inch to 15 inch conventional steel wheels. There isn't a Baby Moon that fits an 8 inch tire and wheel. But if you can tell me the diameter of the center pilot holes on your wheels then I can make other recommendations. view full answer...
We do offer options to dress up a trailer wheel, but unfortunately we don't offer any wheel covers that would be compatible with the your wheel/tire combo. Your wheel lacks the nubs (for the lack of a better term) that a hub cap would grab onto.
The closest thing we offer would be a wheel/tire using a conventional steel wheel like # AM32352 which could be used with a baby moon hubcap like # AM90086. view full answer...
The Americana Baby Moon Trailer Wheel Center Cap # AM90086 is intended for 13-, 14- and 15-inch conventional steel trailer wheels like # AM20504 that have three projections around their center, as shown in the linked photo. The cover's inside diameter of 9-1/4-inches matches up to the outsides of these projections for a snug snap-on fit.
The cover will not work on spoke wheels with triangular cutouts like Dexstar Steel 8-Spoke Trailer Wheel # AM20522. view full answer...
Based on the dimensions you mentioned needing for a baby moon cover the # AM90086 that you referenced would be the correct fit. I attached a review video for more info on it as well. view full answer...
it would be a very tight fit but it is possible for The Wheel Club # WI490 to fit your 13 inch tires with the baby moons on them. A safer bet would ne the Rack'em lock, # RA-25. It doesn't cover any part of the center of the wheel so the baby moons would not be in the way. I have included links to video reviews of both locks for you. view full answer...
The Dexstar Steel Spoke Trailer Wheel - 15" x 5" Rim - 5 on 5 - White Powder Coat # AM20428 will allow you to use the Trailer Wheel Center Cap, Chrome, 3.19" Pilot Size # 319EZ. This style cover is currently the only fit to give you a nice finished look. You can then use Americana Trailer Wheel Lug Nut - Chrome Plated - 1/2"-20 # AM90049 to complete the overall appearance. view full answer...
The part you need is the Phoenix USA Front Hub Cover w/ Pop Out - 10 on 225mm - ABS Plastic - Qty 1, part # PXQH2001F, you attached to your question.
I have included a video review link below. view full answer...
William, I was not able to find anything for a 16" wheel with 6 lugs. I was able to find Phoenix USA QuickTrim Ring Cover for 16" Trailer Wheels # QT6556CLO which is a trim ring that works with 16" x 6 wheels, and the Replacement Center Cap for 15" or 16" Aluminum Viking Series Wheels # CXF104B which is a center cap that also works with 16" x 6 wheels.
From what I can see, the closest hubcap I could find would work with a 16 1/2" wheel that use 8 lugs, unfortunately. view full answer...
Currently we do not offer a baby moon style hubcap which fits the Dexstar Vintage Steel Wheel # AM20395 you found. Typically a Baby Moon Hubcap # PX1307SS requires a Conventional wheel like the Wheel # AM20514 which has a raised section for the hubcap to press onto. This Hubcap # PX1307SS has a 10-1/2" outer diameter so you may be able to create mounting tabs which you can add to the mounting studs to hold it in place, if you are unable to find another hubcap for this wheel elsewhere. view full answer...
Since your conventional style trailer wheels are 15 inch in diameter the correct baby moon cover would be the part # AM90086 that you referenced. view full answer...
There really aren't any anti-theft measures you can use to prevent theft of the Wheel Masters Wheel Covers part # WM319580. They basically will just pop onto your rims and would be removed by the same process.
The good news is that these don't look like hubcaps or wheel covers when installed so people probably wouldn't think to steal them as they look like part of the wheel. view full answer...
Paint can openers and flat screwdrivers are normally what is used to remove baby moon wheel covers like the # AM981306. Just be careful and you won't damage the cover. view full answer...
I did some looking around and it looks like we only have baby moon hubcaps that would work on as large as 16" diameter wheels, like the Phoenix USA Baby Moon Hub Cover 12" Diameter # PX1309SS. I've linked our entire selection of baby moon style hub caps for you to look at and see if there are any that you might be able to make work on your 1958 Chevy Apache in the event that you need smaller than 12" diameter baby moons. view full answer...
First we would need to determine what trailer wheel size you would need before we can find a baby moon hubcap that would fit it.
The first thing you will need to determine is the bolt pattern of the hubs you have on your trailer. To do this check out the help article I attached. With this information you will know what wheels can bolt up to the hubs of your trailer.
From there you will want to check out the other link I attached that will take you to a page that has all of the wheel and... view full answer...
The Wheel Masters Lug Nut Covers # WM8011 that you referenced do fit the size lugs you mentioned of 1-1/16" which is commonly found on Ford RVs like your 1997 Ford E-350 Class C so it will fit but they are all press-on style covers. There aren't two of these that would screw on. We do not have a setup like that available. view full answer...
Go To Results